AlarmSystemStore.com BBB Business Review

Fire-Lite FCPS24FS6 6amp Power Supply and Battery Charger

Quick Overview
Fire-Lite FCPS24FS6 6amp Power Supply and Battery Charger The FCPS24FS6 is an 6 amp remote power supply with battery charger. May be used with 12 or 24volt systems. This unit...

Available : In Stock

$356.95

Ship out same day or within 24 hours
Add to Wishlist

Fire-Lite FCPS24FS6 6amp Power Supply and Battery Charger

The FCPS24FS6 is an 6 amp remote power supply with battery charger. May be used with 12 or 24volt systems. This unit will supply additional power for accessories such as bells or any other device that needs power. You can use it when you have maxed out the power outputs on your main panel.

This also features a battery charging circuit which can charge up to 18 A battery.

Specifications:

  • Primary (AC) Power
    • FCPS-24FS6: 120 VAC 60 Hz, 3.2 A maximum
    • Wire size: minimum 14 AWG (2.0 mm) with 600V insulation.
  • Control Input Circuit
    • Trigger Input Voltage: 9.0 to 32 VDC.
    • Trigger Current: 2.0 mA (16 - 32 V).
    • (per input) 1.0 mA (9 - 16 V).
  • Trouble Contact Rating
    • 5.0 A at 24 VDC.
  • Auxiliary Power Output
    • Specific Application Power - 500 mA maximum.
  • Output Circuits
    • +24 VDC filtered, regulated.
    • 3.0 A maximum for any one circuit.
    • 4.0 A maximum total continuous current for all outputs
  • (Stand-alone mode).
    • 6.0 A maximum total short-term current for all outputs
  • (NAC Expander mode).
  • Secondary Power (Battery) Charging Circuit
    • Supports lead-acid batteries only.
    • Float Charge Voltage: 27.6VDC.
    • Maximum Charge Current: 1.5 A.
    • Maximum Battery Capacity: 18 AH.

Features

  • UL Listed NAC Synchronization using System Sensor,
  • Wheelock or Gentex (Commander Series) appliances.
  • Cascadable up to 10 power supplies (four with Gentex) with strobe timing maintained.
  • Operates as a sync follower or a sync generator (default).
  • Contains two, fully-isolated input/control circuits (triggered from FACP Notification Appliance Circuit [NAC expander mode] or jumpered permanently on [standalone mode]).
  • Optional mounting kit, P/N 90286, to internally house addressable SLC control module (CRF-300 or CMF-300) for alarm activation.
  • Four Class B (Style Y) or four Class A (Style Z) (with ZNAC- 4 Module) Notification Appliance Circuits.
  • 6.0 A full load output (3.0 A maximum per circuit) in NAC expander mode (UL 864).
  • 4.0 A continuous output in stand-alone mode (UL 1481).
  • In stand-alone mode, output power circuits may be configured as resettable (reset line from FACP required) or non-resettable or a mix of two and two.
  • Fully regulated and filtered power output (optimal for powering four-wire smoke detectors, annunciators and other system peripherals requiring regulated/filtered power).
  • Power-limiting technology meets UL power-limiting requirements.
  • Form-C normally-closed trouble relay.
  • Fully supervised power supply, battery and Notification
  • Appliance Circuits.
  • Selectable earth fault detection.
  • FCPS-24FS6
  • 24 Volt, 6 Amp Remote Power Supply
  • DF-52301 & D-025
  • Section: Power Supplies/Accessories
  • July 8, 2004
  • AC trouble report selectable for immediate or 8 hour delay.
  • Works with virtually any UL 864 fire alarm control which utilizes an industry-standard reverse-polarity notification circuit (including unfiltered and unregulated bell power).
  • Requires input trigger voltage of 9.0 - 32 VDC.
  • Self-contained in compact, lockable cabinet (15" [38.1 cm] H x 14.5" [36.8 cm] W x 2.75" [7.0 cm] D).
  • Includes integral battery charger capable of charging up to 18 AH batteries. Cabinet capable of housing 7.0 AH batteries.
  • Battery charger may be disabled via dip switch for applications requiring larger batteries.
  • Fixed, clamp-type terminal blocks accommodate up to 12 AWG wire.

Extended Information